Tired of wasting glue sticks?

Are you tired of collecting the remnants of glue from the table?

Then this lifehack for you!

The essence of the lifehack is that at any temperature of the heater, the glue does not flow out of the nozzle during the idle time of the gun. This allows you to save glue sticks and keep the desktop clean. But the main thing is that the gun stops infuriating the user and the work when using it becomes more enjoyable.

All the details are in this video

Related topics

How to Make a Camera Slider

How to Make a Compact Camera Slider for $5

Portable tripod head for half an hour with your own hands

Are you tired of opening a glass can with a knife? Me too.

I shot a video about a homemade gas burner. I began to think how to illustrate her work. And then at breakfast My wife asked to open a jar of jam. Before I used to do this with a knife. Nevertheless, if there is an opportunity to kill two bears with one shot …

I note that opening the cans with some devices of a different design can damage the cover. In particular, the rubber seal can be damaged or the surface on which this seal is applied may be curved. In both cases, the covers lose their integrity when reused.

The video shows the process of making a Jar Opener and its use

Related topics

How to Make a Camera Slider

Smoke Machine 200 watts DIY

Portable tripod head for half an hour with your own hands

I needed a small gas burner for the thermomagnetic engine project (based on the Curie point). I thought that this simple construction might be of interest to you.

The process of assembly and testing is shown in the video clip

To implement this project, the following products were used: a medical dropper, a broken telescopic antenna and the cheapest Chinese gas burner.

That’s what the burner looks like when it’s assembled.

To show the gas burner in operation, I made a small device, which I will describe in one of the following video clips. I hope you can guess how you can use this gadget.

Handmade Small Gas Jet Improvement Part 2

Thanks to the constructive criticism of one subscriber, the blog produced a new burner. Size became larger and the flame size is reduced. The temperature also increased. The gas is afterburned, since there are no yellow flames. The temperature, judging by the color of the hot steel, reaches 1200 ° C.

The assembly of the burner has even become simpler, and the reliability of the needle attachment has increased.

This video shows a new gas burner and its test

Related topics

How to Make a Camera Slider

Smoke Machine 200 watts DIY

Portable tripod head for half an hour with your own hands

The article tells about the homemade smoke machine, the power of 200 watts, made from improvised materials.

I decided to shoot a little smoke when shooting one of the rollers. I wanted to use tobacco, but I was afraid that it would be difficult to get rid of the smell afterwards.

If you can watch videos, then you do not need to read further.

Few details about the DIY smoke machine

If you have two power sources, then such a smoke generator can be built in a couple of hours. But if you use one power source, you will be deprived of the possibility of operational density and the speed of the flow of generated smoke.

For the operational control of the amount of smoke and flow velocity, this simple fan control unit was built.

04 Diagram of electric control of the fan of the machine smoke.

The electrical circuit was assembled on a piece of the breadboard from what was at hand. Probably, it would be possible to build a controller based on LM317 or any DC-DC converter chip. But I chose the scheme on a composite transistor, since it does not have a strict limitation on the maximum permissible supply voltage.

In particular, with the evaporator supply voltage ≈24 Volts, the amplitude value of the rectified voltage, taking into account the range of the mains voltage variation, will be:

24 * 1.05 * √2 ≈ 35.6 (Volts)

And this already exceeds the maximum permissible values ​​of the input voltage of most popular microcircuits – stabilizers. Voltage of the same 24 Volts was selected, proceeding from the available in the presence of nichrome wire AMG24 (0,4мм). The template for spiral winding had a diameter of 10 mm.

The smoke generator works as follows. Glycerin is poured into the evaporator chamber in such quantity that it can be absorbed into the cotton wool. After warming up the spirals, which takes 5-10 seconds, glycerin begins to evaporate. The fan through the air duct pumps air into the evaporator chamber, which mixes with the glycerine vapor and is discharged through the silicone hose. This hose allows you to send smoke to the desired part of the scene during photo-video shooting. Part of the glycerin settles on the inner surface of the hose and when it accumulates a lot, it can be drained back.

The amount of smoke and flow rate can be controlled by changing the supply voltage of both the whole unit and the fan. When the voltage on the fan decreases, the smoke becomes more dense, and the flow rate decreases. If you reduce the supply voltage of the entire smoke of the machine, the amount of generated smoke will decrease.

All accompanying documentation, including the assembly drawing, is in the "Related documentation" section.

About the smoke-liquid

I’m not a chemist and I can be mistaken about the proportions of the smoke of a fluid. But from the recommended proportions: glycerin – 15%, alcohol – 10%, distilled water – 75%, for some reason I began to perspire heavily in the throat. So I used pure glycerin and did not experience any side effects.

Attention! The use of a glycerin-based smoke generator results in the condensation of glycerin vapor on surrounding objects, mostly smooth and cold. For long-term shooting at close range, I recommend to screw the protective filter on the camera to avoid contamination of the front lens of the lens.
Glycerin can be washed off with the help of warm water and any liquid detergent.

Accompanying documentation

This is an assembly drawing of the smoke of a machine, a drawing of a printed circuit board made on the basis of a breadboard, and drawings of templates.

Related topics

How to Make a Camera Slider

How to Make a Compact Camera Slider for $5

Portable tripod head for half an hour with your own hands

About how to make a universal portable tripod head with a panning mechanism from all garbage in just half an hour.

You cannot read an article if you can watch a video.

Gathering on the next trip, I did not take photo accessories with me because of excess baggage weight. And of course these irreplaceable glands were needed on vacation in the first days.

When he returned home, he immediately set to work to next time be fully armed. And I still managed to make a very simple tripod head, the stand for which is a standard plastic bottle. Depending on the choice of bottle shape, this head can be used not only for photo-video shooting, but also for resampling documents.

The head can be installed, not only the phone, but also a compact camera. And for the installation does not necessarily have a tripod socket.

For this head, a panning mechanism was also made, which is often in demand when shooting video. The design is fully functional, takes up little space and weighs almost nothing.

The manufacturing process is lit in the video. The drawings are in the "Additional Materials" below.

If it’s too easy for you, then for you I picked up "Related Topics" for self-made photo and video accessories of a more complex design.

Additional materials

Compact tripod head drawing (90КБ).

Related Topics

How to Make a Camera Slider

How to Make a Compact Camera Slider for $ 5

How to make a speaker with your own hands

Three simple lifhakas for fighting insomnia, implemented at a miserable cost.

Hello dear subscribers and guests of the channel and blog!

With the rapid change of time zones, there can be problems with sleep, which happened with my family. A few hours of insomnia and staring at the ceiling fan pushed me to the idea of using a fan as an activator of audio-video effects that help to fall asleep.

In fact, trying to get yourself to sleep, when you do not want to sleep, is a self-hypnosis. If you do not know the practice of self-hypnosis in perfection, for example, using keywords, then the concentration on audio-video effects will help you. With children can be differently and there much depends on age. Perhaps the effect will have to add a fairy tale.

These effects are known for a long time, but their implementation in the conditions of a lack of tools and materials may be for someone interesting. Then you can not read, but watch the video. For those who want to repeat these homemade, below are published small details.

All materials, except for three staples and tissue paper, were obtained free of charge. Although cigarettes are often wrapped in gifts, so if you did not throw it away … By the way, I collected the red airplane from such paper and it was even brighter than the paper from the set.

Ring office stationery can be requested at the supermarket ticket office. Free cocktail tubes and newspapers are available in any cafe. Capron nazludniki should be somewhere in a shoe store. If you do not find, then you can ask.

As glue will come down that is suitable, up to usual scotch, which can be gently peeled off from any blisters. Although in the video I used some high-tech double-sided scotch, which just happened to be in the place of placement. Its only difference from the usual is that it does not stick to the hands.

Finally, the picture can be downloaded as always from Additional Materials and asked to be printed in the office of the hotel. True, there can only be a black and white printer. But I think the effect will not suffer much.

You can start the effects either all at once, or separately. In the video I show them separately, so that it was clear who was standing on whom (© Bulgakov).

The only thing that should be explained is how it is better to cut the newspaper. The bending and the width of the bands offered in the video make it possible to obtain more random combinations of sounds, which attracts attention better than monotonous noise. This is especially important if you need to "kill" the noise of the air conditioner.

Have a good sleep and a merry holiday dear friends!

Additional materials

Download hypnotic image (0,8MB)

The article describes the design and manufacturing process a slider made from standard parts, purchased at retail. The total costs do not exceed $ 20.

As always, you can see instead of reading boring process of making this a useful tool in a short video report.

Prologue

It has long wanted to get a rail slider for revitalization and better watchable movies.

First look ready solutions on Aliexpress, but there price sliders to 1.2 meter starts from $ 160.

Then I reviewed the internet a lot of homemade, but they either were too shabby, either require a lot of manual work and the specific materials that do not find in our stores..

Then I went to the local special stock markets and there in the tent, where they sell furniture accessories, saw a very interesting, steel, chrome tube length 3 meters. The seller said he could on the spot to cut the tube in half. It was exactly what you need to start the project.

On the same day sketched drawing of the slider, the basis of which I took this same pipe and steel mounting plates that are looked after on the same market in a tent hardware products. Then, when looking for fasteners, I saw the same plate and in DIY stores.

The necessary parts and materials

For the manufacture of the slider will need the following parts and fasteners. Fastener really took a lot. But the slider was conceived notable.

Key details

Pipe furniture Ø25x3000mm – 1pc. – $3.75

Plate mounting 160x60mm – 6 pc. – 0,5×6 = $3

The front tie-threaded M4x20mm – 8 pc. – $1.6

Bearing 4x11x4 – 12pc. – $1.8

Bolt 3/4"x25mm – 1pc. – $1.5

Fixing details

Washer M12 – 4+1=5pc.

Nut М6 – 12pc.

Screw М5х16 – 12pc.

Nut М5 – 12шт.

Washer М5 – 24pc.

Spring waesher М5 – 12pc.

Pin М4х1000мм – 1шт.

Screw М4х45 – 2шт.

Screw М4х10 – 16+6=22pc.

Nut М4 – 8+6+6=20pc.

Washer М4 – 16+6+6=28pc.

Spring washer M4 – 16+8+6+2=28pc.

Screw М2,5х10 – 16+4=12pc.

Washer М2,5 – 4pc.

Spreng washer M2,5 – 16+4=20pc.

Expenses

Details – $11,65

Fixture – $5-6

Total: Less than $20

Drawing slider

The drawing shows the basic concept of the rail slider. To reduce friction during movement of the carriage, miniature ball bearings were used. They are located at 120 degrees to each other, and securely hold the carriage rail at any position. All other drawings required for the completion of parts and assembly of the slider are in “Advanced Materials”.

Completion and production of racks that hold the bearings

I have not had the patience to wait for the arrival of the finished racks from China, and I produced their own steel rod with a diameter of 6mm.

First, sawed bars on the workpiece with a margin of about 1 mm to be processed.

Then he made a parting and chamfering using the coarse and fine file.

Stake the center of each side of the workpiece.

Drill through hole in two stages, drills Ø2…3 and Ø3,3mm.

Note that the full face cut in steel thread to a depth of 20mm – a rather difficult task, even with the presence of a tap wrench. Simplify it can be either slicing a thread only to a depth of 5-6 mm on each side, or to ream the hole Ø3,4 and Ø3,5mm even under the “Chinese” thread.

Production of press brake

For bending threaded racks M4h20mm from M12 washers matrix was produced by cutting angled slots.

And for slots hexagonal pillars should be flat.

A cylindrical, respectively – cylindrical.

To fix the rack on the matrix, with each side of the rack has been screwed on the screw and washer.

As punch was applied rod Ø10mm, but instead press – a massive hammer.

Here is the result of bending cylindrical rack.

Brass Rack better to stick with a press, so as not to break. I used to be a bench screw press.

Making the upper bearing mount assemblies

To set the upper (in the drawing) bearing in the mounting plate was drilled four holes up to 12.5mm diameter.

Better for this use a drill with sharpening tsefenbor (tsapfenbor), whose central part has a diameter of 5mm.

In the absence of such diameter drill holes you can cut it out round file.

When finalizing the M12 washers, each was drilled four holes Ø2,1mm.

Then, the same washer M12 were used as conductors in coaxial Ø2,1mm for drilling holes in the mounting plates. Washers recorded two steel plates, strapped bolts. Thus, each washer has been marked so that the assembly could align its holes with the very holes that have been drilled through it.

In consequence, in the plates were tapped M2,5.

Holes in Ø2,1mm washers M12 were drilled to a Ø2,6mm to M2,5 mounting screws.

Four studs at 34mm were cut off each for fixing the upper bearing.

Making shaped screws for fastening pipes

To protect the pipes from deforming and simplifying the assembly process, the screws were fabricated shapes. First M5 washers were bent on a cylinder with a diameter of 25mm.

And then for these washers using active flux and tin-lead solder was soldered M5h16 screws.

Making shaped sleeves

Shaped as sleeves, tubes and extending between the mounting plates, M6 nuts have been used, in which propylene was first cylindrical groove.

And then this slot has been finalized with a steel cylinder with a diameter of 25mm and a large hammer.

The form of the resulting surface was monitored on the end face washers Ø25mm.

Drilling holes in the pipes

Before drilling, were tested perpendicular mating parts.

Before drilling, were tested perpendicular mating parts.

As well as the position of the conductor with respect to the pipe.

And the distance between the pipes.

And only after that the pipes were drilled.

When all assembly units were ready, it remains only to collect a slider, according to the drawing. The assembly process is better to see in the video, which is located at the beginning of the article.

Brakes for rail slider

Progress slider carriage is so light that the slider can be used as a spirit level. Therefore, for the fixation of the carriage during transport and installation of the slider, a brake is required.

Brake unit consists of only three parts: a plate of fiberglass, brake pads made of genuine leather and the clamping screw M2,5.

Feets slider

As is known, large set rail sliders with two racks. And although I drilled at each site reference slider over the hole for the photo-screws 1/4″, two tripods I had not. Therefore, the question of the legs to the slider is open.

Screw the legs, which are usually equipped with factory sliders, I just did not like. Spin the multi-screws are not wanted, and simple design, I did not come up on the basis of finished parts.

Up-arm leg thing and does not come as a simple and more comprehensive solution was found. But first a little digression.

During assembly of the rail slider, I decided to shoot a few action scenes, which again needed a slider, which has not happened. So I hastily gathered from the second slider has acquired parts of the first. Read more about this slider, which can be assembled in 15 minutes, spending just $ 5, read or look here >>>

Then it was found out that in order to install the slider can quite amiss a pair of ordinary wooden chairs.

Actually, these chairs and determine the final design of the legs, whose role has been assigned to the four eccentric cut from fiberglass.

This form allows the cam lock slider on the chair.

If you want to install the slider on an uneven surface or to adjust the tilt of the spontaneous movement, enough to turn the cam to the desired angle and lock its position with the screw.

Small details

Mounting plates obtained by stamping, have very sharp edges which can injure yourself if you try to stop the move to disperse the carriage. Therefore, follow the brake to release only during video shooting.

I did not blunt the sharp edges so as not to damage the plating. But if you are going to paint the details of the slider, it is better to pre-round all sharp edges of the mounting plate.

Furniture pipe, which I used as the rails are in a pronounced weld seam. On the outer side of the pipe in the area of the seam, using tactile sensations can detect small irregularities. Therefore, prior to attaching the pipe to the base, you need to ensure that these irregularities will not fall into the trajectory of ball movement.

To find the bearing to Aliexpess enter into the search box bearings, and then in the search box on the results 4x11x4 ( «x» – English letter X).

Better suited for bending steel sleeve with a through hole. To bend the blind sleeve, they will have to pre-drill.

Find the threaded bushing on our sites may be on keyvodrdam: coupling nut, sleeve nut, sleeve coupling, plate furniture, etc.

On Chinese websites: coupling nuts, threaded spacers, longer hex nut, M4x20, etc.

Additional materials

Download drawings rail slider, designed for shooting a movie (164kb).

Related topics

How to make a speaker with your own hands?

How to Make a Compact Camera Slider for $5

Portable tripod head for half an hour with your own hands

The article talked about how from parts purchased in the store for a few minutes to assemble a universal slider for shooting video and VR-Object-s, not drilled with no holes.

Prologue

While recording video of the construction of a large rail slider, it took some of the scenes take off with the help of mobile cameras. To this end, I decided to hastily erect the easiest parts of the slider is already acquired for the main project. The design was so simple that I collected it in just 15 minutes. If among my subscribers will videoblogery they hope will appreciate the home-made under appreciated.

Of course, I’ll tell you about the rail and the slider, which also will be built entirely from prefabricated parts. But its structure is much more complicated, and financial costs of three times higher.

The three-minute video shows a slider assembly process and the different ways to use it

That’s what it took to build the three-wheeled slider

In the picture all the necessary parts and materials for the assembly of three-wheeled slider.

The main parts and assembly units

1. Plate mounting 160x50mm – 3pc. – 0,5 х 3 = 1,5$
2. Corner furniture 15Х25х25mm – 3pc. – 0,1 х 3 = 0,3$
3. Ball suitable size with an outer diameter 10-15mm – 3pc. – 0,25 х 3 = 0,75$
4. Heat-shrinkable tubing (diameter depending on the availability of bearings) – 0,5$
5. Pair of standard photo cards on 1/4” & 3/8” – 1$

Fasteners (the total value of approximately –1-2$)

1. Washers 2mm thickness for alignment mating parts – 3pc.
2. Screws M4x30 or longer – for mounting bearings – 3pc.
3. Screws M4h30 or longer – for mounting bearings – 6pc.
4. Nuts M4 – 12pc.
5. Washers М4 – 15pc.
6. Washer M4 – 9pc.

———————————–

Total: max 5…6$

Production of video wheel slider

It is hardly necessary to talk about the process of assembling the slider, the more so because there videoillyustratsiya above. I just tell about how "shod" bearings. This can be done by using a hair dryer or a lighter construction. Although lighter use is undesirable, since uneven heating in the flame tube at the thickness may vary around the perimeter of the bearing is stronger than when more evenly heated by hot air.

The fact that the magnitude of detonation (fine vibration) of the slider depends not only on the quality of the surface on which the slider slides, but also on the wheel radial runout. In particular, the wheels on the toys that have been in my possession, did not provide an acceptable level of detonation.

The tube, which I used as a tire, too, is not perfect, and introduces some non-uniformity in the movement of the camera. However, it improves the adhesion of the slider wheel with the supporting surface and protects the latter from damage.

To improve the ride, it is necessary to burden the slider, which creates an additional burden on the supporting surface. In the apartment there exists little perfect surfaces and most likely they will be varnished or polished panels of furniture. "No shoes" bearings can be left on these surfaces traces.

Use the slider for video capture and VR-Object-s

Here’s what happened as a result.

Slider of this design allows the camera to move in a straight line or concentric path which is determined by the angle of rotation of the wheels.

If necessary, remove the three-wheeled slider allows row VR-Object-s (3D models) or a panorama.

Use this slider it was so comfortable, and the design was so successful that I decided to develop the idea that this slider can be taken on the road. For this I used the platform as a thin-walled steel disk from an old lamp. According to the plan, it will be used as ballast bag of sand. Moreover, the experience of using a ballast of sand I had been >>>

To enhance the tripod head mounting bolt 3/8 "cemented paving two homemade large diameter washers. Without these goals, knocking slider resulted in a rocking tripod head with the camera.

The wheel assembly was replaced by the usual furniture squares on the shorter and thicker, which allowed them to cut thread M4. Now, if the tension screws, performing the role of the rotary axes will be weakened tightening will need only a screwdriver.

Small details

When choosing a path of movement of the slider, it takes quite a precise adjustment of the angle of rotation of wheels. For this to become possible, the screws holding the ball bearings are selected so long.

Not soon, when the trajectory of the movement is rotation about the axis of the slider, it is necessary several times to adjust the angle of rotation of each wheel. The first time it took me five minutes. But when I realized the logic of movement three-wheeled platform, it began to occupy less than a minute. Manage this slider is as easy as to put the car on parking in a bottleneck.

Related topics

How to Make a Camera Slider

How to make a speaker with your own hands?

Portable tripod head for half an hour with your own hands

For information on how to make the speaker and the speaker of the plastic bottle that can compete with cheap computer speakers.

Hello friends!

During the two-liter bottles of beer drinking, I made a bet with a friend that I can make the speaker of that same bottle..

Just before I shook flat coil for another project, and on the table at this time were the magnets bought on Aliexpress. In general, the idea was in the air.

What it was all over, you will be able to see and hear right now, if you watch the movie. For the rest, I wrote a short commentary on the pictures.

If you do not want to read boring text, watch the video.

For the winding plane of the coil is required to make a simple device.

Pre-curing adhesive is made by heating coils of electric shock, in the same way as is done in the repair of speakers. But, however, when using the Deaf schёchek, it takes about a day.

Teflon gasket allow to separate the coil from the device.

Additional coil sizing increases reliability.

Once fully cured adhesive coil is deformed and it is necessary to align with a hair dryer and the press. Adhesives “BF-2″ and “BF-4 ‘are more elastic at a temperature of 150 ° C without deterioration of the properties.

Get a smooth edge when cut with scissors it was harder PET bottles than to heat a piece of nichrome wire.

This process of giving final shape of the future dynamics of the body.

The hole will need to mount the magnet.

Some neodymium magnets with holes, ordered on Aliekspress used by the speaker. The distance between the edge of the magnet and the upper edge of the speaker enclosure can be adjusted by means of washers.

The diffuser is made of some kind of cardboard packaging.

To build the mobile system was used double-sided tape.

The idea of ​​using a polyethylene film as a suspension dynamics inspired by design isodynamic head.

Here is the membrane factory isodynamic speaker.

Fixing to the diffuser on the membrane.

Крепление катушки к диффузору.

The flap writing paper increases the reliability of the mobile system.

Installation of mobile systems in the enclosure.

Installation speaker in acoustic design.

For a long time wanted to show how it is possible to tin enameled wire using Aspirin.

Be careful and do not in any case, do not inhale the toxic fumes!

It remains to add a damping filler and connect the coil terminals to the cable.

This is the result.

Tests talking bottle.

You can listen to a speaker playing, if you will look the clip from the beginning of the article.

Pay attention to other popular themes, linked to the end of the article.

Creative success!

Hot Topics

Самодельные колонки для компьютера

Перемотка динамиков

Центровка динамиков